• Categories Cloud
    This will be shown to users with no Flash or Javascript.
  • Directory Statistics
    • Active Links: 110832
    • Todays Links: 0
    • Active Articles: 4129
    • Todays Articles: 0

Trusted Site Seal

Error. Page cannot be displayed. Please contact your service provider for more details. (18)


Free Directory SubmitArticle Details

Explosion Proof Fan

Date Added: June 18, 2012 07:23:19 PM
Author: Oleg Tchetchel
Category: Business & Economy

Fans are often used to handle a variety of gases, dusts and materials other than clean air. Some of these gases and solid particles are combustible. When mixed at certain concentrations, ignition can result in an explosion. Even systems which are normally “safe” can become explosive under abnormal conditions. System designers must consider the safety hazard that each component of the system carries. This discussion presents some considerations that must be given to the fan. Almost any fan could serve in explosive environments under normal operation. The temperatures encountered are low enough that few (if any) materials will ignite. However, fans have been involved with causing explosions since the fan operating integrity varies over its life. In order to reduce the risk of explosion, fan construction is modified. A widely used standard for specifying these modifications is the Air Movement and Control Association’s (AMCA) Standard 99-0401, “Classification for Spark Resistant Construction.” This standard has the following characteristics: 1) It identifies who is responsible for what. 2) It allows for three different levels of construction: Type A, B, and C. 3) It is general in nature to allow different fan manufacturers to comply using alternative methods. 4) It provides disclaimers and warnings to users concerning residual risks. 5) It does not require qualification testing. While not explicitly stated, AMCA 99-0401 is limited to applications for which the explosive materials are present in a sealed ducted airstream, but not present on the outside of the fan housing. For all classes of spark resistance, bearings and electrical devices (motors, sensors, etc.) are not allowed in the direct airstream. From the lowest level of protection to the highest, the classifications of spark resistant construction are: Type C: The fan is designed so that if the impeller or shaft comes loose and shifts during operation, two ferrous parts will not come into contact. Type B: In general, this requires a nonferrous impeller and a nonferrous rubbing ring around the shaft hole. Also, extra locking systems are required to prevent the fan impeller, shaft, and bearings from shifting. Type A: This requires a nonferrous airstream. Also, the extra locking systems are required as in Type B. All spark resistant types require the fan to be electrically grounded so as to prevent static electricity from building up. The end user is responsible for installing the ground strap. A common material used by fan manufacturers in achieving spark resistance is aluminum. The AMCA standard provides a warning that aluminum rubbing on rusty steel will create sparks. It is the end user’s responsibility to ensure that steel surfaces are suitably coated, and that fans are kept clean from iron oxides. The AMCA standard allows fans to be constructed of any material which has “demonstrated ability to be spark resistant.” Metals containing less than 5% iron are allowed. Although aluminum is the most common construction material, copper, brass, Monel, and other metals are used where corrosion and temperature limit the suitability of aluminum. NOTE: Stainless steel does NOT comply. Non-metallics are often avoided as a construction material for the fan impeller due to the potential for buildup of static electricity. Some fan wheels are constructed of fiber reinforced plastic (FRP) which has an electrically conductive surface coat. This coating should be electrically grounded to the shaft. The AMCA standard is widely used in the United States, and is referenced by other standards. An equipment specifier need only state “AMCA Spark Resistant Type B” to convey a multitude of fan design requirements. The standard is effective in that the risks of fan-induced explosion can be dramatically reduced without excessive cost additions. Internationally there are other standards which are used. At the time of writing this article there is a developing European “CEN” standard. This standard is attempting a much more comprehensive approach to this subject. While the AMCA standard does not claim to make fans truly “explosion proof,” the CEN standard may well make that claim. It could do this by including many more considerations that may be relevant in reducing the likelihood of an explosion, including: - Fan modifications required to accommodate the presence of explosive environments outside the airstream. - A more limited set of construction materials. - Specifications on design durability and other mechanical aspects. - Requirements on gas stream sealing, motor construction, bearing design and shafting design. - Fan qualification testing. - Operating temperature limits. - Maintenance and cleaning requirements. Oleg Tchetchel Ventilation Specialist Buffalo Fan Co. http://buffalofan.com/index.html http://buffalofan.com/custserv.html
 
Ratings Average rating: (0 votes)
Comments

No Comments Yet.


Visual Confirmation Security Code

*Enter the code shown:  

  • Help
  • Featured Website
  • Natural Skin Care - Expederm
  • Twitter Ticker
    Twitter icon

    My tweets

    Loading..
  • Latest Links
  • Latest Articles
    Rudimentary Criteria In Roofing Described
    Examining Systems Of Roofing, The Options For Root Criteria For Roofing, Compared - Roofing Solutions, Thinking About Core Factors For Roofing